铝木复合隔音门制作要注意哪些技术要求？
(1)制作隔音门时，门扇芯内应用超细玻璃棉丝或岩棉填塞，但不宜挤压密实，应保持其松软状态，以确保其隔音效果。
(1) the production of sound insulation door, the door of the core of the application of superfine glass cotton yarn or rock wool packing, but should not squeeze dense, should maintain its soft state, to ensure its sound insulation effect.
(2)门扇与门框之间的缝隙，应用海绵橡皮条等弹性材料嵌入门框上的凹槽中，粘牢卡紧。海绵橡皮条的截面尺寸，应比门框上的凹槽宽度大1mm，并凸出框边2mm，保证门扇关闭后能将缝隙处挤紧打严。
(2) the gap between the door and the door frame, a groove application of sponge rubber elastic material such as embedded on the door frame, secure locking. The section size of the sponge rubber strip should be larger than the width of the groove on the door frame, and the 1mm of the convex frame is 2mm, so that the door can be tightly pressed after closing.
(3)双扇隔音门的门扇搭接缝，应做成双L形缝口。在搭接缝的中间，应该设置海绵橡皮条。当门扇关闭时，搭接缝两边会将海绵橡皮条挤紧，门扇之间应留2mm宽的缝隙，接头处木材与木材间不应直接接触。
(3) the door of double sound insulation door should be made into double L shaped joint. In the middle of the joint, sponge rubber strip should be set. When the door is closed when the joint on both sides will sponge rubber squeezing, the door should be kept between 2mm wide gap, no direct contact should be at the joint between wood and wood.
(4)外包隔音门宜用人造革进行包裹。在人造革与木门扇之间应该填塞岩棉毯，然后用双层人造革压条规则地压在门扇表面，再用泡钉将之钉牢，人造革表面应包紧、绷平。
(4) outsourcing sound insulation doors should be covered with artificial leather. In artificial leather and wood door should fill rock blanket, and then use the double leather layering pressed on the surface of the door leaf and the rules, the bubble nail nail, artificial leather surface should be tightly wrapped, beng.
(5)在隔音门扇底部与地面间应留5mm宽的缝隙，然后把3mm厚的橡皮条用通长扁铁压钉在门扇的下部，与地面接触处的橡皮条应伸长5mm，封闭门扇与地面间的缝隙。
(5) 5mm wide gaps should be noise in the bottom part of the door leaf and the ground, and then put the 3mm thick rubber nail door in the lower part of the long flat iron pressure, rubber in contact with the ground at the elongation of 5mm, and the ground between the gap closed door.
(6)有防水要求的隔音防火门，门扇可用耐火纤维板制作，两面各镶钉一块5mm厚的石棉板，再用26号镀锌铁皮满包，外露的门框部分亦应包裹镀锌铁皮。
(6) the waterproof and fireproof door with waterproof requirements, the door leaf can be made of refractory fiber board, the two sides are studded with a 5mm thick asbestos plate, and then the full use of galvanized iron sheet No. 26, the exposed door frame part should also be coated galvanized iron sheet.
(7)隔音门的五金，应与隔音门的功能相适应，如合页应选用无声合页等。
(7) the hardware of sound insulation door should be adapted to the function of the sound insulation door, such as the hinge should use the silent hinge.
